Dryer installation precautions
Maintenance of the machine is an extremely important and regular task. It should be closely coordinated with extreme operations and overhaul.
The personnel are on duty.
Dryer installation
1. When the dryer is transported by the manufacturer to your laundry room, you must first perform a routine inspection of the dryer to check whether it is the machine you purchased and whether it is damaged or not used during transportation. Problem, if you have problems, you should take photos immediately and contact the manufacturer.
2. Before the dryer, you should determine the installation position of the dryer. The installation position of the dryer should consider the location of the transportation channel, raw material turnover, water intake, steam inlet and sewer pipe. Here, the Xingxing washing equipment reminds you of the dryer. It should be installed together with equipment such as dehydrators and dryers to reduce the distance between these devices and prevent subsequent troubles caused by improper selection of positions.
3. The dryer belongs to one of the larger and heavier laundry equipment, so the machine should be installed on a solid foundation, and at the same time, it should be kept horizontal to prevent the equipment from being caused by the uneven location of the site and the installation location. Large vibrations occur during work, which affects washing efficiency and the service life of the dryer.
4. Refer to the instruction manual of the dryer, and find the electrical control cabinet door of the industrial washing machine according to the relevant contents in the manual. Connect the 380V three-phase power supply line and the neutral line according to the binding post. (There is a reminder here: the dryer Power must be 380V, no access to low voltage or high voltage)
5. Refer to the drying machine body label to indicate the corresponding access to the water inlet pipe and the steam pipe. If the steam condition is not available, the steam inlet port may be blocked. If steam heating is used, install pressure indicating devices and safety devices at the obvious location of the steam main pipe outside the machine.
Dryer installation test
1. The equipment should be installed on a level concrete foundation and fixed with anchor bolts.
2. When installing, pay attention to the vertical direction of the main body and the horizontal.
3. After installation, check whether the bolts in all parts are loose and the main door is tight. If necessary, tighten them.
4. Configure the power cord and control switch according to the power of the device.
5. After the inspection is completed, the empty load test is carried out, and the test can be carried out normally.
Installation note
1. Drying properties of the material - drying curve, critical moisture content, and equilibrium moisture content under the selected drying conditions.
2. Physical and chemical properties of materials - morphology, water content, water content, water of crystallization, particle size, bulk density, viscosity, heat sensitivity, softening point, phase transition point, thixotropy, toxicity, corrosiveness, odor, flammability, explosiveness , electrostatic, gas permeability, agglomeration, crystal or particle smashability...
3. The impact of material commodity value and drying effect on it. Such as product moisture, pollution, temperature, wear, chalking, crushing, rehydration, etc. on the value of the commodity.
4. Dry production requirements and long-term planning.
5. The upper and lower sequence process of the material drying process. (involving the state method of feeding and discharging)
6. The requirements of the dryer for material recovery.
7. Available heat sources (coal, fuel, electricity, gas, liquefied gas, natural gas)
8. The drying method of the material in the past or the drying method of similar products.
9. Environmental protection requirements - restrictions on dust emissions, noise, vibration, odor, volatiles, etc.
10. Installation site size, with or without special requirements.
11. User's operator level and maintenance capabilities.
12. The amount of purchase funds that may be invested, local labor, land, and energy prices.
13. Select the appropriate dryer according to the local average annual temperature and humidity.
The installation of the industrial washing machine is completed by the operation of the dryer installation test. At the time of installation, we should also pay attention to the following problems:
1. The installation environment of the work dryer is the best for dry, ventilated and clean working environment, good working environment and key factors for extending the service life of the dryer.
2. When installing, you should strictly refer to the installation contents provided by the manufacturer to carry out the step-by-step operation. Do not install it according to your own feelings.
3. When there is a problem during installation, you should contact the manufacturer at the first time.
Note: When using, pay attention to the safety of children and the safety of adults. Specifically divided into different types of dryers, with different types of dryer instructions
Acrylic Sheets,Acrylic Sheets for Kitchen,Alabaster Acrylic Sheet
UV Boards,Wardrobes Co., Ltd. , http://www.wall-board.com