Analyze how the plastic crusher operates safely
(1) Preparation before operation:
1. Carefully check whether the power cord of the equipment is damaged or damaged, and the grounding device is good to prevent electric shock.
2. Open the knife and the crushing bin to check if there are any residual plastics and other foreign objects. If there are foreign objects, clean them in time.
3. Close the crushing bin and tighten the fixing screws.
(2) Operating procedures and methods:
1. Turn on the power, start the device, and carefully check whether the device is operating abnormally.
2. After confirming that the equipment is running normally, put in the materials that need to be broken.
3. After the material in the knife is completely broken, put in new materials.
4. Once the blade is stuck, you must immediately turn off the device and turn off the power before proceeding.
5. The device can be started again only after the fault is processed.
(3) After the operation:
1. Turn off the switch after the material is broken and cut off the power.
2. Open the knife and the crushing bin to clean the remaining materials in the crushing bin.
3. Close the crushing bin and tighten the fixing screws.
4. Pack the broken plastic into the woven bag and place it in the designated position of the workshop.
5. Clean up the equipment machine and the surrounding ground.
(4) Safety operation procedures:
1. It is strictly forbidden to put too much into the plastic when it is broken, causing the card to die and burning the motor.
2. When the equipment is running, it is strictly forbidden to put your hand into the crusher to operate, so as not to cause injury.
3. It is strictly forbidden to put hard objects and the like into the crusher to cause damage to the blade.
4. It is strictly forbidden to place water bottles, scissors, blades and other sundries on the equipment to prevent foreign objects from falling into the feeding port and damaging the equipment.
5. Regularly lubricate and maintain the operating parts.
Concerned about surprises
Label: Analyze how the plastic crusher operates safely
Previous: The difference between centrifugal oil filter and ordinary oil filter Next: Repair and maintenance of plate heat exchanger
Graphite Powder soft, dark gray; greasy feeling, can contaminate the paper. Hardness of 1 to 2, along the vertical direction with the increase in the hardness of the hardness can be increased to 3 to 5. Specific gravity of 1.9 to 2.3. In the isolated oxygen conditions, the melting point of more than 3000 ℃, is one of the most resistant minerals. At room temperature, the chemical properties of Graphite powder is relatively stable, insoluble in water, dilute acid, dilute alkali and organic solvents; materials with high temperature conductive properties, do refractory materials, conductive materials, wear-resistant lubricating materials.
Graphite powder is widely used, according to its different use, we can be divided into the following categories of graphite powder
1. Scale graphite powder
Flake Graphite powder is the most widely used, but also processed into other graphite powder of the original material, scaly graphite powder specifications from 32 to -12000 mesh range, scaly graphite powder toughness is good, with good thermal conductivity and corrosion resistance, can be used as refractory Materials, wear-resistant lubricating materials, conductive materials, casting, Fansha, die and high temperature metallurgical materials
2. Colloidal Graphite powder
Colloidal graphite is formed by the average dispersion of graphite particles below 2u meters in an organic solvent. Colloidal graphite is a viscous suspension of black filaments. Colloidal graphite powder with high quality Natural Flake Graphite performance, in high temperature conditions with special oxidation resistance, self-lubricating and plasticity, at the same time with good conductivity, thermal conductivity and adhesion, mainly used in sealing, metallurgical stripping and other industries
3. Ultrafine graphite powder
Ultrafine graphite powder specifications are generally between 8000 mesh -10000 mesh, mainly used in powder metallurgy release agent, the production of graphite crucible, the battery anode and make conductive materials additives
Nano-graphite powder main specifications for the D30 50 100 400 nm, nano-graphite powder process is more complex, low production rate, so relatively high prices, mainly used in anti-corrosion coatings, lubricants additives, grease additives, precision graphite seal And other industries, in addition, nano-graphite powder in scientific research institutions also has a high application value
5, High Purity Graphite powder
Graphite Powder
Graphite Powder,Nano-Graphite Powder,Graphite Carbon,Carbon Brush For Graphite Powder
Fengcheng Ruixing Carbon Products Co., Ltd , http://www.lnfcrxts.com